TESEQ ProfLine 2103

TESEQ ProfLine 2103

適用于小型DUT的低成本系統完整的測試系統，包括純凈電源模擬閃爍阻抗，不需要昂貴的物理阻抗

應用標準：IEC 61000-3-2 和 IEC 61000-3-3特點：Mains supply options: ProfLine 2103-240System contents:NSG 1007-3-240 Power sourceCCN 1000-1 1-phase coupling unitDAQ cardInterface cableWIN 2100 H&F test softwareWIN 2110 PQT test softwarePre-configured PCUSB cable

ProfLine 2103 is an accurate and flexible single phase system designed to measure harmonics and flicker in accordance with IEC 61000-3-2 and IEC 61000-3-3, supporting testing on products consuming up to 11 Amps rms and 92 Amp peak @230 Vac. The system is supplied complete with a stable, accurate, programmable 3 kVA power source. The ProfLine 2103 system is therefore ready to measure and record any harmonics and flicker created by the EUT. A wide range of higher power AC source systems are available from Teseq, please see ProfLine 2105, 2115, 2130, 2145 datasheets for suitable systems at higher power or for 3-phase operation.Measurements are made using precision, no burden, active hall-effect current transformers connected via a dedicated cable to a multichannel fast Data Acquisition Card (DAQ) fitted inside a PC. One voltage and three current measuring channels are used to make simultaneous measurement of both current and voltage. Calculations are made using dedicated Teseq software (WIN 2100) to determine harmonics (classes A-D), inter-harmonics, flicker, dc, dt, dmax, Pst, Plt, inrush current and 24 x dmax.ImpedanceMeasurement of flicker requires a fixed, stable source impedance as specified in IEC 61000-3-3 (0.24 ? + j0.15 ? in the line and 0.16 ? + j0.1 ? in the neutral). The precision power source (NSG 1007-3) supplied as part of the system is able to accuray simulate this impedance by careful control of the relationship between voltage and current. This eliminates the need for a costly physical impedance. However, hardware lumped impedances are available from Teseq, see options list.Power quality measurementThe power source (NSG 1007-3) supplied as part of the ProfLine 2103 system is able to perform tests in conformance to a number of immunity standards. IEC 61000-4-13 (immunity to harmonics and interharmonics), IEC 61000-4-14 (voltage fluctuations), IEC 61000-4-17 (ripple on DC) and IEC 61000-4-28 (variation of power frequency). Additionally it can also perform pre-compliance testing to IEC 61000-4-29 (voltage dips, interrupts and variations on DC supply) and IEC 61000-4-11. With the addition of further options IEC 61000-4-8 (power frequency magnetics) and fully compliant IEC 61000-4-11 (voltage dips, interrupts and variation on AC supply) can be implemented.Mains supply options ProfLine 2103-240System contents NSG 1007-3-240 Power sourceCCN 1000-1 1-phase coupling unitDAQ cardInterface cableWIN 2100 H&F test softwareWIN 2110 PQT test softwarePre-configured PCUSB cablePower source (for full specification see separate datasheet)Power output (AC mode) 3,000 VAVoltage AC, two ranges 0-150 V and 0-300 VMaximum current (low range) 22.2 Amps, 110 Amps peak repetitiveMaximum current (high range) 11.1 Amps, 96 Amps peak repetitiveFrequency range (AC mode) 16 Hz – 1000 HzPower output (DC mode) 2,100 wattsVoltage DC, two ranges 0-200 V and 0-400 VMaximum current (low range) 15.6 AmpsMaximum current (high range) 7.8 AmpsSupply 1-phase, 240 Vac L-N, 50/60 HzDimensions (HxD) 178 x 483 x 610 mmWeight 28 kgCoupling unitNumber of phases 1Measurement channels 4EUT connector: Front panel CEE 77EUT connector: Rear panel Terminal blockMaximum voltage: Front panel 240 VacMaximum current: Front panel 16 ArmsMaximum voltage: Rear panel 300 VacMaximum current: Rear panel 40 Arms (200 A Pk for 10 ms)Supply power: Voltage 115/230 Vac +/- 10%Supply power: Current<0.5 ASupply power: Frequency 50/60 HzDimensions (HxD) 89 x 427 x 560 mmWeight 5 kgDAQ card and cableInterface PCISize Standard heightResolution 16 bitSpeed 250 kSamples/sCable length PC to CCN 2 mPCMinimum specificationProcessor Pentium 2 GHzRAM 2 GBHard disk 80 GBOperating system Windows XP or VistaINA 2151, 1-phase IEC 61000-3-3 16 Amp reference impedanceCCN 1000-1L, 1-phase coupling unit with integrated IEC 61000-3-3 16 Amp impedanceINA 2188, Rack mounting kit for CCN 1000-1INA 2189, Rack mounting kit for NSG 1007-3Option 8, 1 m magnetic loop antenna 100 A/m continuousOption 11-1, 1-phase AC switch used to switch power between the source (set to the lower required voltage) and the mains supply in a time between 1-5 us. For detailed specification please see separate datasheet.Avionics immunity & emissions test capability for DO-160, Airbus and Boeing

TESEQ ProfLine 2103

深圳市美佳特科技有限公司（簡稱“美佳特"）成立于2010年，致力于光通訊測試、通用電子測量及5G測試服務。美佳特以“無線溝通，溝通無極限 "企業使命，業務聚焦于精密測試測量儀器的租賃、銷售、維護、計量及測試環境搭建等一站式服務。N2843A Keysight 無源探頭 Keysight 是德

主營產品：示波器主機和模塊、眼圖儀、光譜儀、信號源、頻譜分析儀、網絡分析儀、阻抗分析儀、光通信儀器、誤碼儀、光時域反射儀、可調諧激光源、光功率計、光衰減器等。合作品牌：安捷倫、是德、泰克、安立、愛得萬、安騰、力科、馬可尼（IFR）、R&S、EXFO等。N2843A Keysight 無源探頭 Keysight 是德

主推：Agilent 86100D/C 示波器,keysight M8195A 任意波形發生器,Anritsu MS9740B/A 光譜分析儀,YOKOGAWA AQ6370D/E 光譜分析儀,keysight N1092A/C 采樣示波器,keysight E8257D 模擬信號發生器,keysight E5071C 矢量網絡分析儀